973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

Rooflight Sheet – Metal Sheet Compatible

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

Out of stock

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: Rooflight Sheet – Metal Sheet Compatible

Extruded polycarbonate sheets, corrugated or trapezoidal, with one or two co-extruded layers of UV protection.

Application and Advantages

  • Sheet metal roofing
  • Saw teeth
  • Transparency
  • Impact Resistance
  • Cold bending

Product specification

  • Reaction-to-fire certificate to EN 13501-1: classification B-s1,d0.
  • 10-year warranty

Recommended installation

  • Fixing system The fixing system must allow free expansion of the plate, therefore rigid fixings or through bolts are not recommended.

  • Structure. A transversal support structure is required, which can be of any nature or geometry. In the modulation, the maximum dimensions of the sheet must be respected according to the profile and the loads to be supported.
  • Bearing structure. The maximum spacing between purlins must be determined for each profile, depending on the load to be supported and the maximum allowable deflection. In any case, this may never be higher than 1.20 m.
  • In case of large purlin spacings (greater than 1.20 m), intermediate supports must be installed.
  • Dilatation of the plates. The thermal expansion coefficient of polycarbonate is significantly higher than that of structures and other plastic products, therefore, it is essential to provide systems that allow the free expansion of the sheets. It is necessary to drill holes with a diameter 3 mm larger than that of the screw.
  • Plate length. Long sheets (greater than about 7 meters) accumulate longitudinal expansions of high absolute value and should therefore be avoided whenever possible.
  • If larger spans are required, transverse overlaps of 150 to 250 mm are recommended, depending on the slope of the roof.
  • Layout of the plates. The specially UV-protected side indicated is the one that should go outside. For in-situ sandwich roofs, it is recommended to always install the white-diffusing membrane on the exterior face and the colorless membrane on the interior face.
  • Fixing of the plates. Polycarbonate profiles can be drilled using standard drills and bits. The profiles must be firmly fastened to avoid vibrations; special care must be taken to drill at right angles. The holes must always be drilled at a minimum distance of 50 mm from the edges of the sheet.
  • Sealed. Neutral silicone should always be used. Under no circumstances may polyurethane foam be used.
  • Solape. The longitudinal overlap is made in the opposite direction to the wind or rain direction. The transverse overlap should not be less than 200 mm above the beam. Each plate must protrude 100 mm from the fixing line of the beam.
  • Safety Do not step directly on the plate. The slabs are not passable.

Measurements

Trapezoidal profile of the metal sheet compatible rooflight sheet: 32 mm rib, 200 mm pitch, 1,000 mm cover width
Trapezoidal profile: cover width 1,000 mm, overall width 1,093 mm, 32 mm rib, 200 mm pitch. Dimensions in mm.

Permissible load

Load table

Load (kg/m²)6090120150
Distance between supports (cm)1101009585

Minimum roof pitch: 10%.

Technical Characteristics

Technical characteristics

PropertyStandardValue
Thickness—0.9 mm
Maximum recommended length—7,5 m
Minimum bending radius (thermoforming)—7.5 m
Light transmission—Clear: 89% · Opal white: 36%
Coefficient of linear thermal expansionISO 11359-26.5 × 10⁻⁵ K⁻¹ (0.065 mm/m·°C)
Thermal conductivityISO 83020.20 W/m·K
Service temperature (no load, short term)—from −50 °C to +120 °C
Reaction to fireEN 13501-1B-s1,d0

Download technical data sheet (PDF) ↓

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site