973 228 164 · 699 147 762

Support Phone Number

SANDWICH PANEL CATALOGUE

Flashings for sandwich roof panels

Consult available products, compare models, and request a quote for quantities, special lengths, transport, or installation.

CATEGORY PRODUCTS

Choose your model and request a quote

Ver por tipo:

CATEGORY INFORMATION

Features, applications and selection criteria

Roof sandwich panel flashings — Pre-painted 0.6 mm galvanised steel flashings for finishing trapezoidal and standing-seam sandwich panel roofs: ridges, side flashings, front closures, wall flashings, copings and L-shaped corners. Made in 3 m pieces and in seven colours to match the panel.

Which flashing for each part of the roof

Roof area Flashing Reference
Top line of a dual-pitch roof Die-cut ridge or smooth ridge 2015 / 2016
Free side edge Side flashing 2011
Side edge of the panel Side cap 2021
Side edge against a wall Side wall flashing 2013
Top of a mono-pitch roof against a wall Die-cut rear flashing 2014
Front of the panel at the eaves Front end cap 2012
Walls and parapets Coping 2017
Corners and joints Inside and outside L-flashings of 5 × 5, 5 × 7 and 10 × 10 cm 2019–2026

Features of our flashings

  • 0.6 mm pre-painted S250GD galvanised steel.
  • 3 m pieces, sold by the linear metre.
  • Colours: white RAL 9010, red RAL 3009, green RAL 6005, metallic grey RAL 9006, slate grey RAL 7024, blue RAL 5019 and cream RAL 1015.
  • The most common colours are in stock; the rest are made to order.
  • Made-to-measure flashings: another girth, colour or special fold, from your sketch.

How to work out the flashings for a roof

Measure each joint in metres: the ridge, both side edges of each slope, the eaves and any joints with walls. Each piece is 3 m long and overlaps the next by about 10 cm, so it covers about 2.9 m. Divide each length by 2.9 and round up.

Example: a 6 × 4 m dual-pitch shed with 2.2 m slopes needs 6 m of ridge (3 pieces), 4 side edges of 2.2 m (4 side flashing pieces, each cut to length) and 12 m of eaves (5 front end caps).

Installation tips

  • Start side flashings at the eaves and work up to the ridge, so each upper piece laps over the one below.
  • Always fix on the crown of the rib with flashing screws every 30–50 cm, and seal the overlaps with sealant or butyl tape.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder.

More flashings and accessories

See also ridge flashings, side flashings, all flashings, roof sandwich panel and screws.

Frequently asked questions about roof flashings

Die-cut or smooth ridge?

The die-cut ridge fits the panel ribs and closes the gaps by itself. The smooth ridge also works for hips and valleys, but the gaps between the ribs must be closed separately.

Are the flashings the same colour as the panel?

Yes. They are made in the same colours as the roof panel so the roof looks uniform.

Can you make a flashing that is not on the list?

Yes. Send us a sketch with the dimensions and colour and we will make it to measure.

Need a quote?

Send us the dimensions of the job or a sketch and we will prepare the materials list. Write to us from the contact page or call +34 699 147 762.

PERSONALISED QUOTE

Request a price for sandwich panel

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

SANDWICH PANEL SERVICE

Supply, transport and specialised installation

In addition to the product, we can quote for flashing, fixings, sealing, skylights, transport and auxiliary equipment.

The final selection should consider use, thickness, spacing between supports, loads, exposure environment and project requirements.

A service tailored to each project

Technical advice

Help choosing the panel, thickness, finish, fixings and flashing.

Shipping throughout Spain

Transport coordinated according to lengths, quantities, destination and unloading.

Project-based quote

Price tailored to the product, quantities, accessories, transport and installation.

Specialist installation

Assessment of auxiliary equipment, flashings, junctions and work sequence.

OTHER CATEGORIES

Explore all types of sandwich panel

Go straight to the main panel and sheet metal families available.

Tile-effect sandwich panel

Residential finish for homes, porches and refurbishment.

Roof sandwich panel

Insulated panel for industrial, agricultural and residential roofs.

Facade sandwich panel

Vertical cladding with visible or concealed screws.

Agropanel for farms

Agropanel for livestock and agricultural environments.

Cold room sandwich panel

Solution for cold rooms and temperature-controlled spaces.

Rock wool sandwich panel

Options with specific fire and acoustic performance.

Wood sandwich panel

Insulation and a natural decorative look.

Corrugated metal sheet

Lightweight profiles for roofs and enclosures.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site