973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

2016 – Smooth Ridge Flashing

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: 2016 – Smooth Ridge Flashing

The 2016 is a smooth ridge flashing for trapezoidal and standing-seam roof sandwich panels. It closes the ridge of the roof with a folded sheet without die-cut edges. Because it is smooth, it works for several joints: ridges, hips, valleys and changes of pitch.

It is made in the same colours as the roof panel, so the flashing blends in with the roof.

Characteristics

Reference2016
TypeSmooth ridge flashing
Where it is usedRidges, hips, valleys and other joints between slopes.
PanelTrapezoidal and standing-seam roof sandwich panels
MaterialPre-painted galvanised steel sheet
Thickness0.6 mm
ColourWhite RAL 9010, red RAL 3009, green RAL 6005, metallic grey RAL 9006, slate grey RAL 7024, blue RAL 5019 and cream RAL 1015
Piece length3.15 m (3.00 m useful)
SoldBy the linear metre
AvailabilityThe most common colours are in stock; the rest are made to order.
FixingFlashing screws
Smooth ridge flashing (ref. 2016): dimensioned cross-section for roof sandwich panels
Ridge flashing cross-section. Dimensions in mm.

How to install it

  1. Close the gaps between the ribs at the ridge with foam fillers or sealant.
  2. Place the first piece at one end, resting on the crowns of the ribs of both slopes.
  3. Overlap the pieces by about 15 cm, with the laps facing away from the prevailing wind, and seal the overlap with a bead of sealant or with butyl tape.
  4. Fix the ridge with flashing screws on the crowns of the ribs, on both sides.

Installation tips

  • Do not skip closing the ribs: without it, wind drives rain and snow through the gaps under the ridge.
  • In valleys the flashing collects water from two slopes: make generous overlaps and seal them well.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3.15 m long and overlaps the next one by about 15 cm, so it covers 3.00 m. Divide the length by 3 and round up. For example, for 12 m you need 12 ÷ 3 = 4, that is, 4 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

What are a hip and a valley?

A hip is the projecting edge where two slopes meet, like a sloping ridge. A valley is the sunken, V-shaped joint where the water from both slopes runs.

Why choose the smooth ridge over the die-cut one?

Because it works with any panel profile and for joints other than the ridge. In exchange, the gaps between the ribs have to be closed separately.

See also ridge flashings for sandwich panels and all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 699 147 762 · WhatsApp.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site