973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

RA1017 – Top Coping Flashing

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: RA1017 – Top Coping Flashing

The RA1017 is a top coping flashing for aged ochre tile-effect sandwich panels. It covers the top of walls and parapets. It protects the top of the wall or panel from rain, and its legs run down both faces so water cannot get into the joint.

It comes in the same colour as the tile-effect panel, so the flashing goes unnoticed and the roof keeps its tiled look.

Top coping flashing (ref. RA1017): 3D view for tile-effect sandwich panels in aged ochre
3D view of the coping flashing.

Characteristics

ReferenceRA1017
TypeTop coping flashing
Where it is usedTops of walls and parapets.
PanelAged ochre tile-effect sandwich panels
MaterialPre-painted galvanised steel sheet
Thickness0.50 mm
ColourAged ochre, matching the aged ochre tile-effect panel
Piece length3 m
SoldBy the linear metre
AvailabilityIn stock in our warehouse.
FixingFlashing screws
Top coping flashing (ref. RA1017): dimensioned cross-section for tile-effect sandwich panels in aged ochre
Coping flashing cross-section. Dimensions in mm; A ≥ 80 mm; B = panel thickness + 5 mm; X to suit the job.

How to install it

  1. Check that the top of the wall is clean and level; if needed, fit a support batten.
  2. Place the coping centred on the wall, with the legs running down both faces.
  3. Overlap the pieces by about 10 cm and seal the overlap with a bead of sealant or with butyl tape.
  4. Fix the legs with flashing screws if the wall is panel or sheet metal, or with plugs and screws if it is masonry, every 30–50 cm.

Installation tips

  • Give it a slight fall towards the roof side so the water does not stain the façade.
  • Measure the total width of the wall including finishes: if it does not match the standard coping, we make it to measure.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3 m long and overlaps the next one by about 10 cm, so it covers about 2.9 m. Divide the length by 2.9 and round up. For example, for 12 m you need 12 ÷ 2.9 = 4.1, that is, 5 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

Can it be made for a wider wall?

Yes. We make the coping to fit your wall; we only need the total width and the height of the legs.

Is it suitable for masonry walls and panel walls?

Yes. Only the fixing changes: plugs and screws in masonry, and flashing screws in sandwich panel or sheet metal.

See also all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 699 147 762 · WhatsApp.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site