973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

RG1014 – Die-Cut Rear Flashing

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: RG1014 – Die-Cut Rear Flashing

The RG1014 is a die-cut rear flashing for slate grey tile-effect sandwich panels. It closes the top of a mono-pitch roof that ends against a wall. Its die-cut edge follows the shape of the panel ribs and closes the gaps between them.

It comes in the same colour as the tile-effect panel, so the flashing goes unnoticed and the roof keeps its tiled look.

Die-cut rear flashing (ref. RG1014): 3D view for tile-effect sandwich panels in slate grey
3D view of the rear flashing: upstand against the wall and edge cut to fit the tiles.

Characteristics

ReferenceRG1014
TypeDie-cut rear flashing
Where it is usedTop of mono-pitch roofs that end against a wall.
PanelSlate grey tile-effect sandwich panels
MaterialPre-painted galvanised steel sheet
Thickness0.50 mm
ColourSlate grey, matching the slate grey tile-effect panel
Piece length3 m
SoldBy the linear metre
AvailabilityMade to order.
FixingFlashing screws
Die-cut rear flashing (ref. RG1014): dimensioned cross-section for tile-effect sandwich panels in slate grey
Rear flashing cross-section; the lower leg is cut to the tile profile. Dimensions in mm.

How to install it

  1. Fit the panels of the slope, leaving the top end a few centimetres short of the wall.
  2. Place the flashing with the die-cut edge fitted over the ribs and the vertical leg against the wall.
  3. Overlap the pieces by about 10 cm, lining up the die-cut edges with the ribs, and seal the overlap with a bead of sealant or with butyl tape.
  4. Fix the flashing to the crowns of the ribs with flashing screws, and to the wall with plugs or screws. Seal the top joint with the wall.

Installation tips

  • Before ordering, check that the die-cut edges match the profile of your panel.
  • Always fix on the crown of the rib, never in the valley, where the water runs.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3 m long and overlaps the next one by about 10 cm, so it covers about 2.9 m. Divide the length by 2.9 and round up. For example, for 12 m you need 12 ÷ 2.9 = 4.1, that is, 5 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

What does die-cut mean?

The edge that sits on the panel is cut to the shape of the ribs. The flashing fits the profile and closes the gaps without extra pieces.

Can it be used on a dual-pitch roof?

On a dual-pitch roof the top is closed with a ridge flashing. The head wall flashing is for mono-pitch roofs that end against a wall.

See also all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 699 147 762 · WhatsApp.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site