973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

RA1021 – Outside L-Flashing 5 x 7

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: RA1021 – Outside L-Flashing 5 x 7

The RA1021 is a outside L-flashing for aged ochre tile-effect sandwich panels. It is a 5 × 7 cm sheet-metal angle for external corners and edges. It covers the panel edges at the corner, protects the insulation and leaves a straight, clean edge.

It comes in the same colour as the tile-effect panel, so the flashing goes unnoticed and the roof keeps its tiled look.

Outside L-flashing 5 x 7 (ref. RA1021): 3D view for tile-effect sandwich panels in aged ochre
Typical 3D view of an L-flashing.

Characteristics

ReferenceRA1021
TypeOutside L-flashing
Where it is usedExternal corners, edges and around openings.
PanelAged ochre tile-effect sandwich panels
MaterialPre-painted galvanised steel sheet
Thickness0.50 mm
ColourAged ochre, matching the aged ochre tile-effect panel
SizeLegs of 5 × 7 cm
Piece length3 m
SoldBy the linear metre
AvailabilityIn stock in our warehouse.
FixingFlashing screws

How to install it

  1. Fit the panels that form the corner and check that the edge is plumb.
  2. Offer the flashing up around the edge, with each leg on one face.
  3. On vertical corners start at the bottom and work up, so each upper piece laps over the one below; overlap by about 10 cm and seal the overlap with a bead of sealant or with butyl tape.
  4. Fix each leg with flashing screws every 30–50 cm.

Installation tips

  • It also works for finishing the sides and head of doors and windows.
  • For inside corners, use the inside L-flashing.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3 m long and overlaps the next one by about 10 cm, so it covers about 2.9 m. Divide the length by 2.9 and round up. For example, for 12 m you need 12 ÷ 2.9 = 4.1, that is, 5 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

What do the 5 × 7 dimensions mean?

They are the legs of the angle in centimetres: 5 cm on one side and 7 cm on the other. With one longer leg, it suits joints where one face needs more cover than the other.

What is the difference between the outside and inside L-flashing?

The external one goes on projecting corners and edges. The internal one goes in inside corners, where the angle points inwards. The direction of the fold is different.

See also all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 699 147 762 · WhatsApp.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site