973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

2013 – Side Wall Flashing

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: 2013 – Side Wall Flashing

The 2013 is a side wall flashing for trapezoidal and standing-seam roof sandwich panels. It seals the side joint between the roof and a higher wall. One leg sits on the last rib of the panel and the other runs up the wall, so water running down the wall goes back onto the roof instead of getting between the panel and the wall.

It is made in the same colours as the roof panel, so the flashing blends in with the roof.

Side wall flashing (ref. 2013): 3D view for roof sandwich panels
3D view: upstand against the wall and drip edge over the panel.

Characteristics

Reference2013
TypeSide wall flashing
Where it is usedSide joints between the roof and walls or parapets.
PanelTrapezoidal and standing-seam roof sandwich panels
MaterialPre-painted galvanised steel sheet
Thickness0.6 mm
ColourWhite RAL 9010, red RAL 3009, green RAL 6005, metallic grey RAL 9006, slate grey RAL 7024, blue RAL 5019 and cream RAL 1015
Piece length3 m
SoldBy the linear metre
AvailabilityThe most common colours are in stock; the rest are made to order.
FixingFlashing screws
Side wall flashing (ref. 2013): dimensioned cross-section for roof sandwich panels
Wall flashing cross-section. Dimensions in mm; X to suit the job.

How to install it

  1. Place the flashing with one leg on the panel rib and the other against the wall.
  2. Start at the eaves and work up towards the ridge, with overlaps of about 10 cm; seal the overlap with a bead of sealant or with butyl tape.
  3. Fix the panel leg with flashing screws every 30–50 cm and the wall leg with plugs and screws.
  4. Seal the top joint between the flashing and the wall with polyurethane sealant, or tuck it into a chase cut in the wall.

Installation tips

  • The seal along the top edge is the most delicate point: check it every few years and renew the sealant if it has cracked.
  • If the wall is a façade sandwich panel, fix the vertical leg with flashing screws instead of plugs.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3 m long and overlaps the next one by about 10 cm, so it covers about 2.9 m. Divide the length by 2.9 and round up. For example, for 12 m you need 12 ÷ 2.9 = 4.1, that is, 5 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

How is the flashing sealed against the wall?

Most often with a bead of polyurethane sealant or neutral-cure silicone for exterior use. For a longer-lasting result, cut a chase in the wall and tuck the edge of the flashing into it before sealing.

Is it suitable for brick and concrete walls?

Yes. Only the fixing of the wall leg changes: plugs and screws in masonry, and self-drilling screws if the wall is metal or panel.

See also side flashings for sandwich panels and all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 699 147 762 · WhatsApp.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site