973 228 164 · 699 147 762

Support Phone Number

Made to measure

Technical advice

Delivery to site

Specialist installation

SANDWICH PANEL · CONFIGURATION AND QUOTE

RG1019 – Inside L-Flashing 10 x 10

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

Description: RG1019 – Inside L-Flashing 10 x 10

The RG1019 is a inside L-flashing for slate grey tile-effect sandwich panels. It is a 10 × 10 cm sheet-metal angle for internal corners. It covers the joint between two panels that meet at an inward angle and gives a clean finish.

It comes in the same colour as the tile-effect panel, so the flashing goes unnoticed and the roof keeps its tiled look.

Inside L-flashing 10 x 10 (ref. RG1019): 3D view for tile-effect sandwich panels in slate grey
Typical 3D view of an L-flashing.

Characteristics

ReferenceRG1019
TypeInside L-flashing
Where it is usedInternal corners and joints between walls.
PanelSlate grey tile-effect sandwich panels
MaterialPre-painted galvanised steel sheet
Thickness0.50 mm
ColourSlate grey, matching the slate grey tile-effect panel
SizeLegs of 10 × 10 cm
Piece length3 m
SoldBy the linear metre
AvailabilityMade to order.
FixingFlashing screws
Inside L-flashing 10 x 10 (ref. RG1019): typical cross-section for tile-effect sandwich panels in slate grey
Typical L-flashing cross-section; A = 100 mm leg.

How to install it

  1. Fit the two panels that form the corner and clean the joint area.
  2. Offer the flashing up to the corner, with each leg resting on one panel.
  3. If the joint is vertical, start at the bottom and work up; overlap the pieces by about 10 cm and seal the overlap with a bead of sealant or with butyl tape.
  4. Fix each leg with flashing screws every 30–50 cm.

Installation tips

  • If you are unsure about the size, measure how much needs covering on each face of the joint and add a couple of centimetres for fixing.
  • For corners that project outwards, use the outside L-flashing.
  • Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3 m long and overlaps the next one by about 10 cm, so it covers about 2.9 m. Divide the length by 2.9 and round up. For example, for 12 m you need 12 ÷ 2.9 = 4.1, that is, 5 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

What do the 10 × 10 dimensions mean?

They are the legs of the angle in centimetres: 10 cm on one side and 10 cm on the other.

What is the difference between the inside and outside L-flashing?

The internal one goes in inside corners, where the angle points inwards. The external one goes on projecting corners and edges. The direction of the fold is different.

See also all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 699 147 762 · WhatsApp.

ON-SITE SERVICE

Specialist team for sandwich panel installation

We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.

The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.

Sandwich panel installation on site