Side trim for sandwich panel imitation tile slate grey color

SANDWICH PANEL · CONFIGURATION AND QUOTE

RG1011 – Side Flashing

Name: RG1011 – Side Flashing
SKU: RG1011

Configure your panel

Select the available options. We will prepare the price based on dimensions, quantity, transport and installation.

Exterior Color

Metal Sheet Thickness

Stock / On Request

Type of Measure

Clear

Made to measure

Technical advice

Delivery to site

Specialist installation

PERSONALISED QUOTE

Request a price for this product

Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.

QUICK REQUEST

Tell us what you need

Complete the main details and we will prepare a proposal tailored to your project.

683 442 608 683 442 608 info@starmodul.com

First name

Phone

Email (optional)

Delivery city

Project details

Panel type

Service

Approximate area

Thickness

Attach plans or photos

Data protection

I have read and accept the legal and data protection information.

Description: RG1011 – Side Flashing

The RG1011 is a side flashing for slate grey tile-effect sandwich panels. It closes the free side edge of the roof slope: it covers the last rib of the panel and runs down the edge to the wall, so the insulation is protected from rain, wind and sun.

It comes in the same colour as the tile-effect panel, so the flashing goes unnoticed and the roof keeps its tiled look.

Characteristics

Reference	RG1011
Type	Side flashing
Where it is used	Side edges of the roof that do not end against a wall.
Panel	Slate grey tile-effect sandwich panels
Material	Pre-painted S250GD galvanised steel sheet
Thickness	0.6 mm
Colour	Slate grey, matching the slate grey tile-effect panel
Piece length	3 m
Sold	By the linear metre
Availability	Made to order.
Fixing	Flashing screws

How to install it

First fit all the panels of the slope and check that the last one is properly aligned.
Start fitting the flashing at the eaves and work up towards the ridge, so each upper piece laps over the one below and water cannot get into the overlap.
Overlap the pieces by about 10 cm and seal the overlap with a bead of sealant or with butyl tape.
Fix the top leg to the crown of the rib and the vertical leg to the panel edge or wall with flashing screws every 30–50 cm.

Installation tips

If the edge of the slope is not straight, correct it before fixing: the flashing shows up any deviation.
In windy areas, bring the screws closer, to about 30 cm, at the corners and ends of the slope.
Cut the sheet with snips or a fine-tooth saw, never with an angle grinder: the sparks burn the paint and the sheet ends up rusting.

How many pieces do you need?

Measure the total length of the joint you need to cover, in metres. Each piece is 3 m long and overlaps the next one by about 10 cm, so it covers about 2.9 m. Divide the length by 2.9 and round up. For example, for 12 m you need 12 ÷ 2.9 = 4.1, that is, 5 pieces.

Made-to-measure flashings

If your project needs a different girth, another colour or a special fold, we make the flashing to measure. Send us a sketch with the dimensions and we will prepare a quote.

Frequently asked questions

What is the difference between the side flashing and the side wall flashing?

The side flashing is used when the edge of the roof is free, open to the air. The side wall flashing is used when the slope ends against a higher wall and the joint with the wall has to be sealed.

Do I need a side flashing if the panel is already well fixed?

Yes. At the edge of the panel the insulation is exposed and the last rib is open. Without a flashing, water, wind and insects get in, and the foam deteriorates in the sun.

See also side flashings for sandwich panels and all sandwich panel flashings. Need a price? Ask for a quote or call us on +34 973 228 164.