973 228 164 · 699 147 762

Support Phone Number

Sandwich wall panels: which to choose and how to install them

facade sandwich panel installation

To install sandwich panels on walls you must first assemble a substructure of profiles or purlins, start from a corner, fasten each panel with self-drilling screws, seal the joints and finish with the flashings. The panels can be installed vertically or horizontally. In this guide we explain the process step by step, what materials you need and the mistakes to avoid.

Which sandwich panel to use for walls

For walls, facade sandwich panels are used: they are suitable for both exterior and interior walls of industrial buildings, commercial premises, and homes, and can be installed vertically or horizontally. For walls with special requirements (fire, noise, cold, or exposed wood), other types of panels are used:

Wall Recommended panel Thickness Why
Exterior of warehouse, store, or garage Facade with exposed screws 30–100 mm It is the most economical option and the fastest to assemble.
Home or office facade Facade with concealed fastening, smooth or wood-effect 30–100 mm Continuous finish, with no visible screws.
Interior wall or partition Smooth facade with white interior face 30–100 mm Smooth wall that is easy to clean, without the need for wet construction.
Interior with exposed wood Wood panel 30–100 mm Houses, porches, and bungalows with a wood finish that requires no further cladding.
Fire or noise-resistant wall Rock wool panel 50–150 mm Up to EI 240 on facades and better acoustic insulation.
Cold room Refrigeration panel 40–200 mm Watertight joints and thickness according to the room temperature.

The thickness depends on what you need to insulate: we explain this in what sandwich panel thickness to choose. And if you’re unsure between wall and roof panels, check the differences between roof and wall panels.

What you need before you start

  • –
    The facade panels. With exposed screws, more economical and faster to install, or with concealed fastening, for a continuous finish without visible screws. You have all the models in facade sandwich panel.
  • •
    The substructure: metal purlins, tubes or timber battens where the panels are screwed.
  • •
    Screws suitable for the support: for tubes and purlins, for timber or for concrete, and flashing screws for the flashings.
  • –
    Flashings: corners, L and U flashings, plinth flashings, coping flashings and opening flashings. You have them in flashings for sandwich panel.
  • •
    Sealant for exterior, tape or gasket for the joints and foam or mineral wool to fill gaps.
  • •
    Tools: screwdriver with torque limiter, level or laser, tape measure, saw suitable for cutting panel without burning the sheet or the insulation, and lifting and safety equipment according to the height.

Step 1: prepare the wall and the substructure

Review the project documentation and decide the direction of the panels (vertical or horizontal) and the installation order. Check that the base is clean and level and mark the lines where the panels will go.

The panels are not fixed directly to the wall, but to a substructure of profiles or purlins anchored to it. If the panels are installed vertically, the profiles are placed horizontally. If horizontally, vertically. All must be in the same plane: if not, the panels will not fit properly and the joints will open.

At the base, on the plinth, install the plinth flashing or the starter profile, which supports the first panel and prevents water from entering from below.

Step 2: install the first panel

Installation always starts from a corner of the building and, as a rule, from the plinth. The first panel is the most important: if it is crooked, all the others will be too.

  1. 1.
    Present the panel on the starter profile.
  2. 2.
    Check with the level that it is perfectly plumb, both vertically and horizontally.
  3. 3.
    Press it against the substructure and fasten it starting from the top, to prevent deformation.

Step 3: vertical installation

After the first panel, install the next one on the same corner, but on the adjacent wall. This way both faces are aligned from the start.

  • •
    Apply sealant to the tongue-and-groove of the already fixed panel.
  • •
    Fit the next panel into the sealed joint, pressing enough so that the two panels are properly joined.
  • •
    Fasten it to each profile of the substructure.

If the panels do not cover the entire height of the wall, finish the first row and continue with the next one up to the required height. The horizontal joint between rows is protected with a flashing or expansion joint.

Step 4: horizontal installation

  • •
    Install from bottom to top.
  • •
    Align each panel before fastening it.
  • •
    Seal the joint before fitting the next panel.
  • •
    Install each panel with the groove facing downwards relative to the previous one.

This last point is key: if the panels are installed with the groove facing upwards, rainwater remains in the joint, enters the panel and ends up damaging it.

Step 5: panel fastening

The panels are fastened with self-drilling screws with sealing washer. The number of screws is calculated according to the wind load, the position of the panel on the facade and the height of the building: the corners and the upper part bear more wind and require more fastenings. Tighten the screws just enough for the washer to seal without deforming the sheet. A screwdriver with torque limiter helps a lot.

In the panel with exposed screws, the screws go through the panel from the outer face. In the concealed fastening panel, they are placed in the joint area and are covered by the next panel.

Step 6: joint sealing and flashings

For the facade to insulate properly against cold, heat and noise, all joints must be sealed:

  • –
    Seal the joints between panels and around windows, doors and openings. The perimeter gaps can be filled with foam or mineral wool.
  • •
    Install the corner, coping, opening and plinth flashings.
  • •
    Install the flashings overlapping from bottom to top, so that water runs off the outside and does not get in behind.
  • •
    Also seal the junctions between flashings and panels.

Can sandwich panel be installed directly on a wall?

Yes, on brick, block or concrete walls, but always with a substructure of profiles or battens anchored to the wall. This way the panel remains flat even if the wall has irregularities, and can be screwed correctly. Indoors, for example to line a wall or create a cavity, the process is the same.

Common mistakes when installing panels on walls

  • •
    Not plumbing the first panel properly: the error carries through to the entire wall.
  • •
    Horizontal panels with the groove facing upwards: water enters the panel.
  • •
    Overtightening the screws: the sheet sinks and the washer stops sealing.
  • •
    Forgetting to seal joints and gaps: insulation is lost and moisture enters.
  • •
    Cutting with an unprotected abrasive disc: sparks burn the sheet paint and rust spots appear.

You have more tips in common mistakes when installing sandwich panel and in how sandwich panel is installed and fastened. If you are interested in knowing what changes between a facade panel and a roof panel, we explain it in differences between roof and wall panel.

Frequently asked questions

Is it better to install the facade panel vertically or horizontally?

Both options are valid. Vertically, installation is usually faster and water runs off through the joint itself. Horizontally, the facade looks more elongated and is common in commercial buildings. The important thing is to respect the direction of the joints and seal them properly.

What screws are used for the facade panel?

Self-drilling screws with sealing washer, specific to the support: metal purlin, timber or concrete. The length depends on the panel thickness.

What panel thickness do I need for a wall?

It depends on the insulation you need. For warehouses and storage buildings 30 to 50 mm is usually enough, and for housing and offices 60 to 100 mm are used. We explain it in what thickness should sandwich panel have.

How much does it cost to install sandwich panel on a wall?

Installation costs, as a guide, between €18 and €25/m², plus material. You have the detail in how much does sandwich panel installation cost.

Need a quote?

Are you going to enclose a warehouse, a storage building or a house? Send us the measurements of the walls and the openings, and we will prepare the panels to measure with their flashings and screws. Request a quote without obligation or call us on 699 147 762.

PERSONALISED QUOTE

Receive a made-to-measure sandwich panel quote

Indicate dimensions, location, application and required service. The more data we have, the better we can adjust the panel, flashings, transport and installation.