Contact Email
Support Phone Number
SANDWICH PANEL CATALOGUE
Consult available products, compare models, and request a quote for quantities, special lengths, transport, or installation.
CATEGORY PRODUCTS
Ver por tipo:
CATEGORY INFORMATION
Sandwich panel screws — Screws for fixing sandwich panels to any structure (steel purlins, I-beams, timber or concrete) and for stitching flashings. Choosing the right screw for the substrate is what makes the panel withstand the wind and keeps the roof watertight.
Which screw you need for your structure
SubstrateScrewPre-drillingSteel purlins and tubes up to 6 mmPurlin screw: dual-thread 5.5/6.3 self-drillingNoIPN and IPE beams and sections up to 12 mmI-beam screw: long drill pointNoTimber purlins and beamsTimber screwNoConcrete beams and purlinsConcrete screwYes, 5 mm bitFlashings and sheet overlapsFlashing screw with washerNo
Keys to fixing the panel properlyThe screw must go through the panel and the substrate; in steel, at least three threads must protrude below.On roofs, always fix on the crown of the rib, never in the valley where the water runs.Use a screwdriver with a depth stop: overtightening deforms the sheet and spoils the washer seal.Follow the number of fixings per panel and purlin given by the panel manufacturer, especially in windy areas.
How to choose the length
Add the panel thickness at the fixing point and the substrate thickness (or the embedment depth in timber or concrete). The purlin screw page has a guide table: for example, the 82 mm screw suits panels from 30 to 65 mm. If in doubt, tell us the panel and the structure and we will give you the size.
Complete the installationSee the sandwich panel flashings, the steel purlins, the butyl tape and the other mounting accessories.
Frequently asked questions about sandwich panel screws
Why does the purlin screw have two threads?The lower thread taps into the purlin and the upper one grips the outer sheet of the panel and acts as a stop, so the panel is not crushed when tightening.
How many screws do I need per square metre?It depends on the panel, the purlin spacing and the wind in the area. As a guide, roofs usually take 3 to 4 screws per panel at each purlin; check your panel’s fixing plan.
Can I use flashing screws to fix the panel?No. They are short and designed for thin sheet. To fix the panel, use the screw suited to the structure.
Need a quote?Send us the dimensions of the job or a sketch and we will prepare the materials list. Write to us from the contact page or call +34 699 147 762 · WhatsApp.
PERSONALISED QUOTE
Tell us the panel type, area, thickness, location and whether you need supply only or installation. We’ll review the details to prepare a tailored proposal.
SANDWICH PANEL SERVICE
In addition to the product, we can quote for flashing, fixings, sealing, skylights, transport and auxiliary equipment.
The final selection should consider use, thickness, spacing between supports, loads, exposure environment and project requirements.
Help choosing the panel, thickness, finish, fixings and flashing.
Transport coordinated according to lengths, quantities, destination and unloading.
Price tailored to the product, quantities, accessories, transport and installation.
Assessment of auxiliary equipment, flashings, junctions and work sequence.
OTHER CATEGORIES
Go straight to the main panel and sheet metal families available.
Residential finish for homes, porches and refurbishment.
Insulated panel for industrial, agricultural and residential roofs.
Vertical cladding with visible or concealed screws.
Agropanel for livestock and agricultural environments.
Solution for cold rooms and temperature-controlled spaces.
Options with specific fire and acoustic performance.
Insulation and a natural decorative look.
Lightweight profiles for roofs and enclosures.
ON-SITE SERVICE
We quote for new builds, refurbishment, roof and facade replacement, flashing installation, and work with sheet metal or skylights.
The quote depends on geometry, height, access, auxiliary equipment, location, fixings and junctions the job must resolve.