Sandwich panels do not have a single standard measurement: they are custom-made. The most common is an effective width of 1,000 mm, thicknesses from 30 to 100 mm (up to 200 mm for cold rooms) and a custom length ranging from about 2 metres to 20 metres, depending on the model. In this guide, you have the measurements for each type of panel according to their technical data sheets and how to measure your roof or facade to order the exact material.
Sandwich panel measurements by type
These are the measurements included in the technical data sheets for each product. If your project needs something different, please contact us: many measurements are manufactured to order.
Effective width and total width: they are not the same
Panels fit together on one side, so part of their width is covered by the next panel. That is why we talk about two measurements:
-
–
Effective width: what each panel covers once installed. This is the measurement you should use to calculate how many panels you need. In most models, it is 1,000 mm. -
–
Total width: the measurement of the loose panel, including the overlap. For example, the rock wool panel has an effective width of 1,000 mm and a total width of 1,075 mm.
Sandwich panel thicknesses
Thickness is the total thickness of the panel, including the insulating core. Greater thickness means more insulation and more resistance, but also more weight and a higher price. As a guide:
-
•
30 to 50 mm: sheds, garages, warehouses and industrial buildings without high insulation requirements. -
•
60 to 100 mm: homes, offices and industrial buildings where thermal comfort matters. -
•
100 to 200 mm: cold rooms and freezer rooms.
Thickness also depends on the distance between supports and wind and snow loads. We explain this in more detail in what thickness should a sandwich panel be.
Panel length: custom, maximum and recommended
The panel is cut at the factory to your required length, within each model’s range. Pieces over 14 meters are manufactured for corrugated and flashing roof models. In practice, panels are supplied up to 14–20 meters long depending on the model: for longer panel sections, two panels are overlapped, with the upper one mounted over the lower one and the joint sealed. It is important to distinguish two points:
-
•
Manufacturing length: the minimum and maximum that can be made. -
–
Recommended maximum length: beyond this measurement, the panel is more difficult to transport, unload and install, and the expansion of the sheet metal is more noticeable. Longer pieces can be ordered, but it is advisable to evaluate this beforehand.
For tile-effect panels, the length is in multiples of 0.35 m, because it must match the tile pattern.
How many square metres are in a 6-metre panel?
Multiply the length by the effective width. A 6-metre panel with a 1-metre effective width covers 6 m². With this data, you can estimate the price of each piece: we explain it in how much does sandwich panel cost per m²?
To do it in a minute, use our sandwich panel calculator: it tells you how many panels, m², purlins and screws you need.
How to take measurements for your roof or facade
-
1.
Decide on the type of panel. Cubierta, fachada, teja o frigorífico tienen anchos, largos y pendientes mínimas distintos. -
2.
Measure the length of each slope or section. For roofs, measure in the direction of the slope, from the ridge to the edge, and add the eaves or overhang you want to leave. This will be the length of each panel. -
3.
Measure the width to be covered. For roofs, the horizontal length of the slope. For facades, the length of the wall. -
4.
Calculate the number of panels. Divide the width to be covered by the effective width of the panel and round up. For example, a 12 m wide slope with 1,000 mm effective width panel needs 12 panels. -
5.
Mark openings and joints. For facades, note doors, windows and corners. For roofs, skylights, chimneys and wall joints. -
6.
Check the slope. Each model has a minimum slope: 5% for ribbed and joint-cover roofs, 10% for tile-effect panels and 30% for slate-effect panels. -
7.
Don’t forget the flashings and fasteners. Ridges, side flashings and screws are calculated using the same measurements. You can see them in flashings for sandwich panel and fasteners.
Common measuring errors
-
•
Calculating with the total width instead of the effective width: you’ll come up short on panels. -
•
Forgetting the eaves in the length of the roof panels. -
•
Ordering shorter panels and overlapping them when the model allows for the full length: each overlap is a weak point against water. -
•
Not checking the corner bracket of the structure: if it’s not square, the panels will gap and the flashings will not close.
For installation, consult our guide on how to install and fix sandwich panels.
Frequently asked questions
What is the standard measurement of a sandwich panel?
There is no single measurement. The most common is an effective width of 1,000 mm and a custom length, which in most models ranges from 4 to 14 metres, and up to 20 metres for ribbed and joint-cover roofs.
How long is a sandwich panel?
Whatever you need within the range of each model: from about 2 metres for tile-effect and rock wool panels up to 20 metres for ribbed roofs. The recommended length is between 8 and 13 metres depending on the model.
What thickness does sandwich panel have?
Between 30 and 100 mm for roofs and facades, and up to 200 mm for freezer cold room panels.
How many panels do I need for 100 m²?
With an effective width of 1 metre, 100 m² is equivalent to 100 linear metres of panel. For example, 10 panels of 10 metres or 20 panels of 5 metres. Add a small margin for cuts and openings.
Can panels be cut on-site?
Yes, to adjust for openings or joints. Use tools that do not burn the sheet metal or the insulation and protect the cuts from moisture. Ideally, order them to size to minimize cutting.
Do you have the measurements for your project? Send them to us, even if it’s just a sketch, and we will prepare the layout and quote. Request a quote without obligation or call us on 699 147 762.


