973 228 164 · 699 147 762

Support Phone Number

Sandwich panel structure: beams, purlins, and how to build it

sandwich panels for roofing

To install sandwich panels on a roof you need a structure of purlins (horizontal profiles) supported on beams or walls, positioned perpendicular to the slope, properly leveled and at a suitable distance for the panel thickness. As a guide, purlins are usually spaced between 1 and 1.5 meters, and the roof requires a minimum slope of 5% with corrugated panel or flashing, and 10% with tile-effect panel. In this guide we explain how to build the structure step by step, with what materials and what mistakes to avoid.

Fundamental Requirements of the Structure for Sandwich Panels

Properly preparing the supports is the most critical step before installing any roofing. A solid and well-calculated structure ensures that the roof withstands wind, snow weight, and temperature changes without deforming. Before starting, check these points:

  • –
    Strength: the structure must support the panel weight plus the wind and snow loads for your area. For significant works, it must be calculated by a technician.
  • –
    Flatness: all purlins must be in the same plane. If one protrudes or sinks, the panel will rest poorly and the joints will open.
  • •
    Corner bracket: if the structure is not square, the panels will fan out and the trims will not close.
  • •
    Slope: the necessary slope for water to drain according to the panel model.
  • •
    Panel support: the bearing width of each purlin must be sufficient to screw the panel securely.

How to Build the Structure for a Sandwich Panel Roof Step by Step

  1. 1.
    Choose the panel before the structure. The panel model and thickness determine the purlin spacing and minimum slope. If you’re not sure yet, see what thickness the sandwich panel should have.
  2. 2.
    Check pillars, walls, and main beams. Verify they are level and can receive the roof. If resting on block or brick walls, finish the top with a ring beam or support beam.
  3. 3.
    Define the slope. Calculate the height difference between the highest and lowest point of the pitch. For example, a 5-meter pitch at 10% requires 50 cm of drop.
  4. 4.
    Mark out the purlins. Mark their position from top to bottom, perpendicular to the slope. The first purlin goes next to the ridge and the last at the eave, accounting for the overhang you want to leave.
  5. 5.
    Fix the purlins. Atorníllalas o suéldalas a las vigas o a los muros, comprobando con una cuerda o un nivel láser que quedan todas en el mismo plano.
  6. 6.
    Place strips at the supports. Una banda autoadhesiva en la cara superior de las correas reduce ruidos por dilatación y protege el contacto entre materiales.
  7. 7.
    Check the corner bracket and start assembling. Measure the pitch diagonals: if they match, the structure is square. Then you can install the first panel following our guide on how sandwich panels are installed and fixed.

Purlin Spacing

Purlin spacing depends on panel thickness, number of supports, and wind and snow loads for the area. As a guide, on sandwich panel roofs purlins are usually spaced between 1 and 1.5 meters. A thicker panel is more rigid and allows wider support spacing. In areas with heavy snow or wind, purlins must be closer together.

When we prepare your quote, we indicate the appropriate spacing for the panel and thickness you choose. If you already have the structure built, tell us the purlin spacing and we’ll recommend the thickness that fits best.

Load Table According to Purlin Spacing

These values are from the technical data sheet for the 3-rib roof sandwich panel (0.4/0.4 mm sheet, multiple supports, downward load). They indicate the maximum load the panel can withstand based on the distance between purlins. 1 kN/m² is equivalent to approximately 100 kg/m².

Thickness 1.50 m 2.00 m 2.50 m 3.00 m
30 mm 1.44 0.89 0.59 0.41
40 mm 1.80 1.17 0.80 0.57
50 mm 2.20 1.46 0.95 0.67
60 mm 2.60 1.53 1.01 0.72
80 mm 3.07 1.77 1.18 0.87
100 mm 3.32 1.92 1.28 0.94

How to read it: compare the value with your roof’s load (snow, wind, and maintenance for your area). The wider the purlin spacing, the less load the panel can withstand, and a thicker panel can withstand more with the same spacing. Wind also pulls the panel upwards (suction), and there’s another table for that in the data sheet. This is a reference, not a substitute for calculation: for significant projects, the structure must be calculated by a technician. You can also try combinations in the sandwich panel calculator.

Minimum Slope by Panel

Panel Minimum slope
Roofing panel corrugated (3 or 5 corrugations) and flashing 5%
Marseille tile-effect panel 10%
Tile-effect panel (tile red, grey, albero) 10%
Slate-effect panel 30%

Below these slopes water does not drain properly and can enter through the overlaps.

Types of Materials in the Structure for Sandwich Panels

Support Material Main Advantages Considerations
Galvanized Steel High strength, straightness, and durability against corrosion Higher initial material cost
Treated Wood Warm aesthetics in exposed interiors and simple assembly Requires treatment and maintenance against moisture
Precast Concrete Maximum durability against extreme conditions High weight and complex assembly

Metal Structure for Sandwich Panels

This is the most common in warehouses, storage buildings, and medium and large roofs. Purlins are usually rectangular tubes or cold-formed profiles, supported on steel beams or frames. It is straight, does not deform with moisture, and allows greater spans. If you need a complete bolted metal structure, we sell it through Starmodul.

Wood Structure

This is common in porches, sheds, and dwellings, especially when the structure is exposed inside. Use exterior-treated wood, well dried and without deformations, and with sufficient sections so the purlins do not deflect.

Over an Existing Roof or Slab

Sandwich panels can be installed over an old roof if the support is sound and can bear the weight of the new roof. The usual approach is to place battens or profiles on top to act as purlins. If the old roof is asbestos-cement fibre (uralite), its handling and removal can only be done by a company registered in the RERA.

Sandwich Panel Structure at Leroy Merlin, Bricomart, or Obramat

In large stores, you’ll find galvanized tubes and profiles in short lengths, designed for porches and small sheds. For a medium or large roof, it’s more cost-effective to order metal purlins custom-sized for the job, already cut and with the appropriate hardware. We compare prices and service for sandwich panels at Leroy Merlin, Obramat, and Bricomart.

What Screws to Use Depending on the Structure

Each structure requires its screw. All carry a washer with sealing gasket to seal the hole:

The screw length depends on the panel thickness. You have all models in screws for sandwich panels.

Common Mistakes When Building the Structure

  • •
    Purlins too far apart for the panel thickness: the panel deflects and marks under snow weight or when stepped on.
  • •
    Purlins out of plane: the panel rests on some but not others, and the screws end up loosening.
  • •
    Insufficient slope for the panel model: water remains in the overlaps and eventually enters.
  • •
    Forgetting the eave overhang when marking out the last purlin.
  • •
    Mixing metals without protection, such as steel and aluminium or copper in direct contact, which promotes corrosion.

Frequently Asked Questions About Structure for Sandwich Panels

What is the ideal distance between purlins?

It depends on the panel thickness and the loads in the area. As a guide, it’s usually between 1 and 1.5 meters. Consult the load table in this guide or tell us which panel you will use, and we will advise you on the appropriate spacing.

What minimum slope should the roof have?

5% with corrugated roofing panel or flashing, 10% with tile-effect panel, and 30% with slate-effect panel.

Can it be installed over an old roof?

Yes, provided the original support is sound and can bear the additional weight. Normally battens or profiles are placed on top to fix the panel.

Is it better to use wood or metal for purlins?

Metal offers more strength and requires no maintenance. Wood has a warmer finish when the structure is exposed inside.

What type of screws are needed?

Self-drilling screws with sealing washer, specific to the structure material: metal purlin, beam, wood, or concrete.

How to prevent rain noise?

The panel’s insulating core itself dampens noise. Placing elastic strips between the structure and the panel also reduces vibrations.

Need a quote?

Do you have the structure built or in design? Send us the measurements, slope, and purlin spacing, and we’ll recommend the appropriate panel and thickness. Request a no-obligation quote or call us at 699 147 762. To calculate the material, our guide on sandwich panel dimensions can help.

PERSONALISED QUOTE

Receive a made-to-measure sandwich panel quote

Indicate dimensions, location, application and required service. The more data we have, the better we can adjust the panel, flashings, transport and installation.